Power, video and data
Power supply StubEQ active receiver hubs
Power supply passive video receiver hubs
Power supply cable integrator hubs
UTP video passive transmitter +12VDC converter
Power-video-data passive transceiver
Power-video passive transceiver
Power supply StubEQ active receiver hubs
These hubs consolidate all CCTV system cabling using standard EIA/TIA 568B structured building wiring.
They are designed for installation in the IDF/Telecom closet or MDF/Equipment room and have individual floating 28VAC outputs that support at-distance camera loads up to 0.5 or 1 Amp per channel for cable runs up to 1,500ft (460m).
A built-in StubEQ™ video receiver hub ensures a zero loss video signal for connection into a DVR or IP encoder.
Features
- Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive NVT transceiver
- Adaptive StubEQ™ fully automatic 2-band equalization provides adjustment free equalization every time, no manual adjustments required
- Frequency Response DC to 10 MHz
- Automatic-reset fault protection; transient protection
- Ground loop free individually floating outputs
- Diagnostic LEDs show load/no load, miswires, overload conditions and video status
- Limited lifetime warranty
Power supply StubEQ™ active receiver hubs come in three models
NV-32PS42-PVD, 32-channel
NV-16PS42-PVD, 16-channel
NV-8PS42-PVD, 8-channel
The installation for all models is explained here
Power supply passive video receiver hubs
These hubs consolidate all CCTV system cabling using standard EIA/TIA 568B structured building wiring.
They are designed for installation in the IDF/Telecom Closet or MDF/Equipment Room and have independently selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel.
Use with NVT’s PVD™ transceivers for cable runs under 750ft (225m).
A built-in passive receiver hub allows connection to DVR or an encoder for IP transmission.
Features
- Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
- Automatic-reset fault protection; transient protection
- Frequency Response DC to 10 MHz
- Individually floating outputs ensure total ground-loop immunity
- Diagnostic LEDs show load/no load, miswires, and overload conditions
- Wall, desk, or rack-mountable
- Limited lifetime warranty
Power supply passive video receiver hubs come in three models
NV-16PS13-PVD, 16-channel
NV-8PS13-PVD, 8-channel
NV-4PS13-PVD, 4-channel
The installation for all models is explained here
Power supply cable integrator hubs
These hubs combine a 1 Amp/channel power supply with pass through video and telemetry data, for up to 16/4 cameras over UTP wire.
They are designed for installation in the wiring/IDF telecom closet, or at the Control/MDF room and they consolidate connectivity via standard 4-pair RJ45 EIA/TIA 568B compliant premises wiring and pinouts.
Power, video and data connections are made at the camera using a PVD™ transceiver via an RJ45 connector and a single 4-pair cable.
Features
- Independently selectable 24 or 28VAC with 1 Amp max per channel
- Automatic-reset fault protection; transient protection
- Individually floating outputs ensure total ground-loop immunity
- Diagnostic LEDs show load/no load, miswires, and overload conditions
- Power cameras via UTP over significant distances
- Wall, desk or, for 16-channel option, rack-mountable
- Limited lifetime warranty
Power supply cable integrator hubs come in two models
NV-16PS10-PVD, 16-channel
NV-4PS10-PVD, 4-channel
The installation for all models is explained here
Cable integrator hub
The NV-716J-PVD hub is installed in the wiring closet or IDF room and is a "pass-through" wiring device that efficiently consolidates camera power, video, and pan/tilt/zoom telemetry data onto a minimum of 4-pair RJ45 cables.
Power, video and data are converted at the camera using a PVD™ transceiver via an RJ45 connector and a single 4-pair cable.
Up to sixteen cameras are supported.
Features
- Uses any third-party power supply to power cameras via UTP over significant distances
- Cable-management solution from the camera to the Wiring Closet and on to the Control Room
- Wall or rack-mountable
- Limited lifetime warranty
Cable passive integrator
The NV-704J-PVD integrator is installed in the Wiring Closet or IDF room, and is a passive "pass-through" wiring device that efficiently consolidates camera power, video, and pan/tilt/zoom telemetry data onto a minimum of 4-pair RJ45 cables.
Power, video and data are converted at the camera using a PVD™ transceiver via an RJ45 connector and a single 4-pair cable.
Up to four cameras are supported.
Features
- Uses any third-party power supply to power cameras via UTP over significant distances
- Cable-management solution from the camera to the Wiring Closet and on to the Control Room
- Wall or rack-mountable
- Limited lifetime warranty
UTP video passive transmitter +12VDC converter
The NV-226J-PV is a passive (non-amplified) transmitter. Combined with a 24VAC-to-12VDC converter is designed to fit on the back of a fixed 12 VDC camera. It converts 24VAC power from the control room, while delivering real-time baseband (composite) video at extended distances, all over one 4-pair UTP cable.
Features
- Up to 3,000ft (1km) with a NVT DigitalEQ™ Active Receiver
- Up to 1,500ft (460m) with a NVT StubEQ™ Hub
- Up to 700ft (225m) with a an NVT Passive Hub or Transmitter
- Exceptional interference rejection
- Frequency response DC to 10 MHz
- Built-in transient protection
- Limited lifetime warranty
Power-video-data passive transceiver
The NV-218A-PVD is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over UTP telephone wire.
Baseband (composite) signals of any type are supported.
Used at the camera, the transceiver has a 9'' mini-coax mini lead for direct video output connection from the camera. Alongside this coax lead are two sets of screwless terminal blocks for quick pass through connections for the camera‘s Power and Data.
Features
- Up to 3,000ft (1km) with a NVT DigitalEQ™ or active receiver
- Up to 1,500ft (460m) with a NVT StubEQ™ hub
- Up to 700ft (225m) with a an NVT Passive Hub or Transmitter
- Supports "up-the-coax" type control signal up to 700ft (225m)
- Exceptional interference rejection
- Frequency response DC to 10 MHz
- Built-in transient protection
- Limited lifetime warranty
Power-video passive transceiver
The NV-216A-PV is a passive (non-amplified) device that allows the transmission of real-time monochrome or color video over UTP telephone wire.
Baseband (composite) signals of any type are supported.
It allows transmission of CCTV video and low voltage power over UTP cable.
Features
- Up to 3,000ft (1km) with a NVT DigitalEQ™ hub or active receiver
- Up to 1,500ft (460m) with NVT StubEQ™
- Supports "up-the-coax" type control signal up to 750ft (225m)
- Exceptional interference rejection
- Frequency response DC to 10 MHz
- Built-in transient protection
- Limited lifetime warranty
